Bimix users: how much do you use?

Fair Rider, congrats on your little backroom science project.  I do my project in the bathroom myself,,,lol 

You may have to go up to twice the dose that you see others using here, as your strength is half the strength of the "standard" strength prescribed most times.  I have to use 50 units myself, some few more, most less, but each is different.  If it was me, which it isn't, I'd jump to 50 units next time and see.  The strength you are using is weak by comparison to others, so larger increments may be needed to get to the level to succeed.  You mau indeed find you will have to go to 75 or 100 units, which is the strength equivenent of my 50 unit of the higher strength bimix. 

Placement, I have learned from trial and error, is critical in using bimix.  Especially for men with a smaller or atropied penis.  Bimix ,lacking PGE1, doesn't work as well as the trimix or caverject,  but you also avoid the pain....  As to the leaking, I find that bimix works well to close off the leaking and squirting of urine when it is active, making the tissues to swell up, thereby squeezing the whole plumbing system in the penis.  Why you would leak after the drug has stopped working and the erection is gone is a mystery.  I haven't read of anyone having that happen to them.  Not saying it doesn't, just haven't heard of it...If you have a successful injection, take notice if you do leak or squirt during intense stimulation or orgasm.  I would suggest maybe speaking to your doc and getting him/her to up the strength with another prescription, especially after you have had a success with the current vial.  That will give you some feeling for how it needs to be adjusted. 

As usual, this is just discussion, not directions or treatment instructions.  Each must make their own decisions, right?

Maybe I am confused..................lol  A prescription for any strength bimix is made in 1ml increments.  Hence 30 mg of papa/1mg of phen per 1ml of sterile water.  That's the basic strength/basic volume measurement of dilutant that has the drug added to it.  Yours is 15mg of papa/ .5mg of phen per 1ml of sterile water.  To my reasoning, yours is diluted to half strength (30mg vs 15mg and 1.0mg to .5mg per 1ml of dilutent) to mine.  If I'm wrong, someone jump in and straighten me out, please?

 My prescription from Francks is a 5ml (also read as 5cc/500 units) vial of 30/1, costing $57.  This gives me 10 .5ml/.5cc/50unit doses.  A 10ml vial of the same would be $114 more or less.  The pharmacies charge a basic cost based on how much drug is used, not how much volume the vial is. A 5ml vial of 30/1 will cost twice as much as a 5ml vial of 15/.5 because of the cost of the amount of drug used to make each 1ml of that vial.  Again, someone correct me if my reasoning is faulty.

James C.

Placement is in the side of the penis, not too close to the abdomen or too close to the head.  Search the net looking for penis anatomy and look at the internal structures of the penis. that will give you a good idea of what I am talking about.  Inject at the 9 to 10 and the 2 to 3 position.  Use a needle that is long enough to get into the cavities, thru at least 1/4 inch of outer skin and not too far that it passes thru the inner wall of the cavity and into the dividing membrane between the left and right cavities.  There is no difference in the placement of any of the 3 , although it might be said that Caverject and Trimix is more forgiving, by the nature of it's stronger action on the penile tissus than bimix, hence bimix takes a more accurate hit exactly within the cavity with the needle.  The Caverject and trimix will work with more marginal injections than the bimix probably will..That's just speculation on my part...

James C.